The problem is that in order to use that setup I'd have to place a cable in between the two routers, and unfortunately that's not an option. I tried inserting Linksys' MAC adress into the NetGear one's configs, making sure that the later was a repeater, had a different IP adress (out of the range of the Linksys router) and had the same SSID.
Connect the router that you just set up as an access point to one of the available Ethernet router in the network (the main router). Power the router. The second router now is set up and connected to function as an access point.
The non-NETGEAR router repeats your existing WiFi signal instead of broadcasting a new one. You can also use your Nighthawk router as an extender and a non-NETGEAR router as your main router. Note: If you set up your Netgear router as an extender (wireless repeater), important routing functions like network traffic management are not active.
The Netgear WGR614 is a popular and inexpensive 54MBit/s wireless router that can be tweaked to be used as a wireless access point on a threaded LAN. As such, it will contribute to extending the range of the wireless segment of the same LAN or – if the router used does not have WLAN capability – will add WLAN capability to the network. Several access points can be used to extend the range even further.
Follow these simple steps:
Make sure there are no network cables attached to the WGR614 (neither LAN nor WAN)
Make sure your laptop or PC used in the following steps is not connected to the network
Connect your laptop or PC to any of the LAN ports of the WGR614 using a network cable
Log on to the WGR614 via your web browser (usually 192.168.0.1 or similar – check the manual for correct address and default logon credentials)
Disable the DHCP server of the WGR614
Change the IP address of the WGR614 to something else than the IP address of the router
Connect the router to any of the available LAN ports of the WGR614 using a network cable
Configure the SSID on the router and the access point so that they are the same
Configure different wireless channels on each device (use the non-overlapping channels 1, 6 and 11 to avoid interference)
Configure the WGR614 to the same security level and settings as the router, including the access control list
Separate the devices to the edge of their wireless ranges
Please consult the manual and/or the Netgear Support Pages if you get stuck in any of the above steps. The network DHCP server IP address range on the router must not include the IP addresses reserved for the access points. If you have the router (that is connected to the Internet through its WAN port) on IP address 192.168.0.1 and, say, two access points on 192.168.0.2 and 192.168.0.3 respectively, the DHCP range on the router should start with 192.168.0.4 (and end with whatever number you think you will need for your network attached gear). Understand that having duplicate IP addresses on your network will put you in a situation you don’t want to be in, so take steps to ensure that the router and the access points never have the same IP. Note also that this setup will not extend the WLAN range of an unthreaded network, i.e. the access points must be connected to the router via cables in this solution. How to make subscripts in word for mac. If your aim is a wireless-only network, you need to look in to access points with repeater functionality.
Reset Netgear Router Wgr614
Tip: If the router is configured with the internal IP address 192.168.0.n on the LAN try configuring the access points with internal IP addresses that are easy to remember, such as 192.168.0.n+1, 192.168.0.n+2, etc. Cisdem pdf converter 7 1 0 3.
Fairbanks morse scale serial numbers. Waiver. The text in this summary has been prepared with uttermost care but is, despite of this, strictly to be considered a guide to be used in conjunction with normal and cautious computer practice, including the safe operation of electric equipment. I cannot accept liability for your actions. Work smart! Work safe!
Setting Up Netgear Wgr614 Router As Repeater System